Who makes good output transformers these days?

You could contact Heyboer to see what's available. Lundahl Is still in business. Maybe Dave Slagle is making something like this. Then there's Edcor and Hammond.

Intact Audio (Dave Slagle)

RE: Who makes good output transformers these days?, posted on June 30, 2024 at 19:40:02
Iczerman Audiophile Posts: 165 Joined: July 23, 2000	Lundhal=$$$$ Audio note=$$$$ But I did forget about Heyboer...I'll give Alden a call.

RE: Who makes good output transformers these days?, posted on July 2, 2024 at 11:36:27
WntrMute2 Audiophile Posts: 788 Location: Detroit Joined: September 16, 2002	Try Monolith Magnetics. Excellent product

RE: Who makes good output transformers these days?, posted on July 3, 2024 at 20:37:29
Oldbean2 Audiophile Posts: 1012 Location: Midwest US Joined: March 27, 2022	I like Hashimoto (Sansui's former winding operation) for push-pull, but I've not heard their SE offerings Back for a bit again. Ignore me if you like.

RE: Who makes good output transformers these days?, posted on July 5, 2024 at 10:28:24

rage
Audiophile

Posts: 812
Joined: December 17, 2010

Edcor and Hammond.

Last I talked to Heyboer the backlog was pretty long.

RE: Who makes good output transformers these days?, posted on July 7, 2024 at 09:20:10

Best audiotransformers
Industry Professional

Posts: 112
Joined: December 4, 2023

I think you look more for cheap transformers then for good transformers

Try this link: https://sklep.toroidy.pl/en_US/p/TTG-KT88SE-Tube-output-UL-transformer-3kOhm-KT88-300B-SE/566

RE: Who makes good output transformers these days?, posted on July 9, 2024 at 08:25:42

rage
Audiophile

Posts: 812
Joined: December 17, 2010

Cheap transformers for the win.

I'd put select Hammond transformers up against the high end stuff and I bet a lot of people would select the Hammond.

I have Hammond 1650R, push pull - quite good - and there is someone much smarter on here than I am that endorsed that model.

Hammond 1627SEA in SE I have heard good reports and am tempted to buy a set.

I run some 10K Edcor SE outputs, small ones with endbells, maybe 15W rated - I find them quite good. No thunderous bass however.

RE: Who makes good output transformers these days?, posted on July 9, 2024 at 10:02:10
Triode_Kingdom Audiophile Posts: 10401 Location: Central Texas Joined: September 24, 2006	Hammond transformers have often been shown to exhibit higher distortion at low frequencies than other offerings in their class. Whether this is important I suppose depends on the budget.

RE: Who makes good output transformers these days?, posted on July 9, 2024 at 10:18:33

rage
Audiophile

Posts: 812
Joined: December 17, 2010

I recall reading some articles that measured Hammond vs Edcor and possibly vs Triode Electronics and you are correct - some models of Hammond did have more distortion in the LF range.

Too bad Triode electronics is no longer producing their Dynaco Clones.

One of my many favorite posters on here, DF, has explained on a few occasions that different manufacturers will have transformers that really shine in their portfolio. (you're also a favorite TK!)

I'd bet Lundahl would be pretty safe in any impedance ratio - but I've been told more than once that it is easier to wind a transformer with a lower primary impedance - and usually 2500 ohms is what is thrown around for SE.

If I were shopping for SE transformers today I'd be looking in the 2500-3500 ohm to 6 ohm secondary. Single tap secondary - and I might pass on UL taps if I was working with triodes.

I also try to keep in mind Earl Geddes when I pick output transformers - as he's essentially said < 100hz is mostly a product of the room.

RE: Who makes good output transformers these days?, posted on July 10, 2024 at 13:19:50
Best audiotransformers Industry Professional Posts: 112 Joined: December 4, 2023	'

Transformer Impedance, posted on July 11, 2024 at 11:20:54

Triode_Kingdom
Audiophile

Posts: 10401
Location: Central Texas
Joined: September 24, 2006

"If I were shopping for SE transformers today I'd be looking in the 2500-3500 ohm to 6 ohm secondary."

The only problem with this is the fact it isn't optimum for distortion with most of the common triodes. I've had this discussion with a few builders who are more experienced using tubes like the 300B than I am. It's pretty obvious these low-Z designs sacrifice linearity for power, but that seems to be what the market wants. Maybe an abundance of even-order distortion is one of the attractions, but I just can't bring myself to intentionally design an amplifier that way. This is why I haven't yet built a push-pull amp with triode-wired pentodes (6L6, EL34, 6V6, etc). None of the transformers I have on the shelf have a sufficiently high primary Z to do them justice.

RE: Transformer Impedance, posted on July 12, 2024 at 11:30:45
Best audiotransformers Industry Professional Posts: 112 Joined: December 4, 2023	'

RE: Who makes good output transformers these days?, posted on July 12, 2024 at 12:00:38
Best audiotransformers Industry Professional Posts: 112 Joined: December 4, 2023	'

RE: Who makes good output transformers these days?, posted on July 13, 2024 at 00:36:37

Best audiotransformers
Industry Professional

Posts: 112
Joined: December 4, 2023

'

RE: Who makes good output transformers these days?, posted on July 13, 2024 at 11:49:36
Best audiotransformers Industry Professional Posts: 112 Joined: December 4, 2023	'

RE: Who makes good output transformers these days?, posted on July 13, 2024 at 11:55:37
Best audiotransformers Industry Professional Posts: 112 Joined: December 4, 2023	'

RE: Who makes good output transformers these days?, posted on July 13, 2024 at 12:02:07
Best audiotransformers Industry Professional Posts: 112 Joined: December 4, 2023	'

Tube DIY Asylum

Who makes good output transformers these days?

152.131.10.220