|
Audio Asylum Thread Printer Get a view of an entire thread on one page |
For Sale Ads |
12.214.233.55
In Reply to: Err...OK. posted by Cwise on August 23, 2005 at 11:01:13:
And I said so in the post. Also, I'm not biased against Linn. I've read my original post now about 10 times trying to pinpoint where I may have come off as biased. It looks pretty neutral to me. I conceded that there could be sonic differences between a tweaked TD-150 and an LP-12. I did say that I had doubts if it would be a difference worth $1400. (To me, anyway.) The point of the post was to suggest that since the two tables are designed quite similarly, perhaps a tweaked & modded TD-150 would be somewhere in the ballpark of an LP-12.And the LP-12 SHOULD be built better. It costs 10 times more than the TD-150.
If I could afford it, I'd buy one. So where are these cheap LP-12s hiding? There are 3 on Audiogon now, the cheapest of which is around $1400.
Have you modded your TD-150 if I may ask? Just curious.
Follow Ups:
I was thinking that your post was pretty biased because you compared the modern day price of a LP12 to the bargin basment used price of an TD150. If the two decks were in production at the same time, a fair comparison would be to compare the new prices at that time. I think that you are correct in thinking that the TD150 is a great deck. I have yet to do any mods to it (I am finishing up a teres right now, so the 150 is on the back burner). If I can remove the bearing, I am planing on fabricating a carbon fiber subplinth for the 150, but that is a ways in the future.
Yup, I reckon the price disparity may have been a bit off. I never thought of the fact that they were spaced apart by a few years. My fixer-upper Thorens was $50 & the used LP-12s I could find were still in the $1500 range. I can afford $50 for a table. But an armless $650 table of any kind is still out of my price range, at least for the forseeable future.BTW, I don't think an unmodded, untweaked TD-150 is anything to write home about. Especially the Mk.I with that Godawful clunky arm they stuck on there. (The later arm was reportedly much better.) I was comparing an upgraded, damped, modded TD-150 with a good arm like a Linn, Rega, SME, etc. to a stock LP-12 with a similar arm. I think if you performed the right mods to that 150, you'd be pleasantly surprised. It's still (usually, at least) a much cheaper alternative to the venerable LP-12.
Regardless, the Linn is a classic & great table and I never meant to infer otherwise. Enjoy it. I sure would!
TD150 vs LP12 well I have a TD150mkII that I have made a new plinth out of Oak about the same size as the Linn a linn armboard a Rega RB250 arm rewired & express heavyweight , 16V motor power by a Project Speedbox PSU changes 60Hz to 50Hz alot like a Lingo also Linn springs longer bolts for the springs,the table looks like a linn and it sound GREAT!!! Alot like a Linn
yes, i'd like to know too. i would definitely come up with $500 if an LP12 surfaced at that price - even if i had to sell some internal organs. :)
I bought a Linn with the basic power supply, SME III tonearm, NOS Dynavector cart, a crazy amount of extras (carbon brush, kinetic barrier mat, mounting screws, Lube, extra belts and alignment protractor) for $600. I sold the arm for $300, put a rewired rega (total of $150). I had to change the unit from 220 to 120, but that was just a matter of the removal of a cap and new power cord. I bought this guy on ebay, and I think people were scared because it was in the US and wired for 220.
I just saw a LP12 on Audiogon for $650 without arm, and quite a few have gone for cheaper on Ebay. It is not as easy as going out and picking them off the vine, but if you search around, you will be rewarded.
This post is made possible by the generous support of people like you and our sponsors: